▶ VD-9600WHG/B


▶ VD-9500H


▶ VD-1600HD


▶ VD-9000FHD


▶ VD-8000HDS


▶ VD-7000W


▶ VD-5000W


▶ VD-3000


▶ VD-1500MG/MB


▶ VD-1500G/B


Caution before installation
Check the cautions as follows before installation for safe installation and use.
  • DO NOT disconnect the power supply while the system is booting up.Be aware of engine ignition switching for they may disconnect power for short periods of time.
  • It is recommended to only use authorized SD cards with the VisionDrive™ products. Install the product after parking your vehicle in a bright and safe area.
  • Install the system when ignition is off, especially after the power source has been turned off completely.
  • Use the power cable provided with the product for the cigarette lighter power connection for power in the range of DC12V to DC24V. If power wiring is involved, we recommend a professional service for the installation.
  • Prior to the installation, clean the area of the installation where the camera will be positioned.
  • DO NOT eject the SD card while the product is in operation.
Installation procedure
1. Assemble the bracket with the main unit
1. Connect the bracket and the main unit.- Assemble the mounting bracket with the main unit and push it to the direction 1 to secure the lock. You will hear a solid click sound when the main unit is locked to the attachment bracket. Move the bracket to direction 2 to release the bracket.

2. Insert SD card into the unit
3. Insert SD card into the unit

- Insert the SD card as shown in the picture.

- When ejecting the SD card from the unit, turn off the main power completely, and then push in the SD card. The SD card will pop out when pushed in once more. Use of force or other methods to eject the SD card may defect the SD card.

3. Connect cable and attach on windshield
4. Connect cable and attach on windshield.

- Clean the area on the windshield where the unit will be placed.

- For the placement of the unit, it is better to place the unit closer to the center of the vehicle. If the unit is installed on the left or right side of the rear vision mirror, make sure there is room to detach and install the unit if needed. Also be aware of window tinting or other window coatings/shielding which may affect camera visibility.

- The adhesive on the bracket is very strong so partially remove the cover of the adhesive. Use the full adhesive surface area for final installation after correct installation is verified through LCD screen.

- Please proceed cigarette lighter connection after the main cable connection and attachment are finished.

4. Connect to power source to turn on the unit
5. Connect to power source and turn on the unit - Insert the cigarette jack into an appropriate outlet

- Turn on the engine or put the car key at ACC to hear voice notification while the product starts. (LCD screen will be turned on at this moment)

- Blinking of LED lamps after a moment means that the system startup was successful. DO NOT turn off the power source while the system boot is in progress. This may harm the product.

5. Adjust the camera angle
6. Adjust the camera angle

- Move the camera top to bottom to place it to a recordable position while checking the LCD.

- Press [V] button to make the LCD screen show where the camera records. Click it again to turn the LCD screen off. It records continuously even if the LCD screen is off.

- When the unit is attached, set the camera to face the front direction of the 1/2 vehicle.

When the unit is attached, set the camera to face the front direction of the vehicle.
- When the unit is attached, set the camera to face the front direction of the vehicle.
Camera is adjustable and can be rotated 65 degrees to cover desired recording areas.

- Camera is adjustable and can be rotated up to 65 degrees to cover desired recording areas.

- Give the camera a bit strong pressure to adjust the angle of the camera due to the camera is tightened to prevent movements caused by little vibration.

6. Check LED lamps
7. Check LED lamps

- The GPS lamp is red when the GPS signal is not received, and blue when it is received.

- The GPS connection may take a couple of seconds to several minutes, depending on the location of your vehicle.

- The REC lamp is blue when it is recording. It is blue when it is recording a NORMAL file and red when recording an EVENT file after an impact or if the SHOT button has been pressed.

7. Arrange wires
8. Arrange wires using wire holders

- Use the enclosed wire holders to arrange and secure the cables.