PRODUCT



VD-ACTO(MagicTrunk)

>

▶ ACTO-I
BlackBox

>

▶ VD-9600WHG/B

>

▶ VD-9500H

>

▶ VD-1600HD

>

▶ VD-9000FHD

>

▶ VD-8000HDS

>

▶ VD-7000W

>

▶ VD-5000W

>

▶ VD-3000

>

▶ VD-1500MG/MB

>

▶ VD-1500G/B

VD-1500G/B

VD-1500G/B
Installation Precautions
  • DO NOT disconnect the power supply while the system is booting up. Be aware of engine ignition switching for, they may disconnect power for short periods of time.
  • It is recommended to use only authorized SD cards with the VisionDrive®. (The SD card is equipped with the VisionDrive® programs which can have your Black box function properly.)
  • Install the product after parking your vehicle in a bright and safe area. Especially when the system related to car power is needed to be installed, the power source has to be turned off completely.
  • Install the system when ignition is off, especially after the power source has been turned off completely.
  • Use the power cable provided with the product for connection to the cigarette lighter power in the range of DC12V to DC24V. If power wiring is involved, we recommend a professional service for the installation.
  • Prior to the placement, clean the area where the Black box will be positioned.
  • DO NOT eject the SD card while the product is in operation.
  • Eject the SD card only after the power is turned off entirely.
Installation procedure
1. Assemble the bracket into the main unit
1. Connect the bracket and the main unit.

Place the bracket inside the groove of the unit then turn the bracket to fasten. (To separate the unit from the bracket, turn the unit to the opposite direction.)

2. Insert SD card into the unit
2. Insert SD card into the unit

Insert the SD card as shown in the picture. When ejecting the SD card from the unit, turn off the main power completely, and then push in the SD card. The SD card will pop out when pushed in once more. Use of force or other methods to eject the SD card may defect the SD card.

3. Connect cable and attach on windshield
3. Connect cable and attach on windshield

Clean the area on the windshield where the unit will be attached. For positioning of the unit, it is better to place the unit in the middle. If the unit is attached on the right side of the room mirror, make sure there is room to detach the unit if needed. Also be aware of window tinting or other window coatings/shielding which may affect camera visibility. The adhesive on the bracket is very strong. Partially remove the cover of the adhesive, and then use the full adherend to the final.

4. Connect to power source and turn on the unit
4. Connect to power source and turn on the unit

Insert the cigarette jack into an appropriate outlet then turn on the engine. When the power is on, the LEDs will be turned on with voice notification. Blinking of LED lamps means that the system booting has succeeded. DO NOT turn off the power source while the system boot is in progress. This may harm the product.

5. Adjust the camera angle
5. Adjust the camera angle

Move the camera top to bottom to place it to a recordable position.

When the unit is attached, set the camera to face the front direction of the vehicle.
When the unit is attached, set the camera to face the front direction of the vehicle.
Camera is adjustable and can be rotated 210 degrees to cover front to rear recording.
Camera is adjustable and can be rotated 210 degrees to cover front to rear recording.
For better images and operation of the analysis program, ensure that over 1/2 of the vehicle hood area is included in the recorded data.
For better images and operation of the analysis program, ensure that over 1/2 of the vehicle hood area is included in the recorded data.
6. Check LED lamps
6. Check LED lamps

The GPS lamp is red when the GPS signal is not received and blue when it is received. The GPS connection may take a couple of seconds to several minutes, depending on the location of your vehicle. The REC lamp is blue when it is recording as NORMAL files and red light means recording as an EVENT file due to an impact or pressing SHOT button in need.

7. Arrange wires using wire holders
7. Arrange wires using wire holders

Use the enclosed wire holders to organize the cable line.

8. Connect to an external display (Optional)
You can view the video which is currently being recorded by connecting to an external display. Video playback is not supported on the external display. (Video-out cable is an optional item available from where you have purchased this product.)